Marcello
Yeni Üye
Kayıt Tarihi: 2021-18-Agustos
Aktif Durum: Pasif
Gönderilenler: 37
|
| Gönderen: 2021-22-Aralik Saat 05:35 | Kayıtlı IP
|
|
|
In addition to the ability to process a diverse range of
different types of workpieces, there is an extensive
selection of different processing methods from which to
choose. The processing methods and technical requirements
for different types of workpieces are, in general, more
or less complex than those for the same type of
workpiece. It is required that parts are only transferred
to the next procedure after they have been thoroughly
inspected and accepted by the previous procedure,
according to the processing procedures. This will ensure
that all parts have been thoroughly inspected and
accepted before being transferred to the next step in the
process. It is recommended that finished parts not be
placed directly on the ground, but rather that
appropriate support and protection measures be used to
ensure that the ground is not damaged during the
installation. There are no permitted defects on the
the surface of the processed thread, including but not
limited to black skin, bumps, randomly buckled and burred
threads, or any other defects permitted on the surface of
the processed thread. The surface of the processed thread
is also not permitted to have any defects on it.
If you want to ensure that the forgings penetrate
completely into the workpiece, make sure that the
forgings are produced on a forging press with sufficient
capacity.
If forgings are to function properly, it is necessary for
them to be completely free of visible cracks, folds, or
other appearance defects that would impair their use or
performance if they were to be used or performed
incorrectly. Even though it is possible to
remove localized defects from a part, the cleaning depth
should not exceed 75% of the total metal CNC machining
allowance for the component. Abrasion should not occur on
the forging's non-machined surface, and any sharp
transitions between the forging's various surfaces should
be avoided.
It is not permitted to have white spots on forgings, nor
are internal cracks or residual shrinkage holes caused by
shrinkage allowed to exist.
To be considered successful, the processing of
welding parts must adhere to a strict set of guidelines.
Before beginning the welding process, check to see that
all defects have been completely removed to
ensure a successful weld outcome. It is also important to
ensure that the groove surface has been repaired in a
smooth and non-sharp manner.
Shovelling, grinding, carbon arc gouging, gas cutting,
and cnc
machining services are all methods
that can be used to remove a defect area from a piece of
welded metal and each has its own advantages.
Cleaning must be done carefully and thoroughly within
20mm of the welding area and groove in order to ensure
that no dirt, sand, oil, water, rust, or other debris
gets into the welding area or groove. Cleaning must be
done carefully and thoroughly within 20mm of the welding
area and groove. If possible, clean the welding area and
groove within 20mm of the welding area.
To ensure that the welding process is completed
successfully, the preheating zone must be maintained at
or above 350 degrees Celsius throughout the welding
process.
It is recommended that the horizontal position be used
whenever possible when it is feasible and when the
circumstances permit it.
While the repair is being completed, it is critical to
keep an eye on the welding rod to make sure that it does
not experience an excessive amount of lateral movement.
In surface surfacing welding processes, weld beads with
overlaps that are less than one-third the width of the
weld bead are not permitted to be used because they would
compromise the structural integrity. All attempts should
be made to avoid welding on visible burns, cracks, and
nodules on the welding surface, as well as any other
imperfections on the welding surface, should be made to
avoid welding on them.
It is not possible to detect any defects such as bite
marks on the meat or the addition of sl*g during this
process because the welding wave is consistent throughout
the entire process. The surface is completely smooth with
no pores, cracks, or splashing.
(4) The specifications document contains a detailed
description of the die-casting process.
Cold partition is not permitted on the surface of a
casting and neither are cracks, shrinkage holes, or
penetrating defects. Cracks, shrinkage holes, and
penetrating defects are not permitted on the surface of a
casting. The presence of serious incomplete defects (such
as undercasting, mechanical damage, and so on) on the
surface of the casting is also prohibited. B. In the case
of a formalized
The castings must be thoroughly cleaned before they can
be used to ensure that the finished product is free of
burrs and flashes, which are undesirable characteristics.
Pouring risers that are flush with the casting surface
must be cleaned prior to casting on a non-processed
surface in order to achieve a smooth pouring surface on
the finished cast when casting on a non-processed
surface.
When a casting is not machined, a clear and
distinguishable cast character or mark should be clearly
visible and distinguishable on the non-machined surface
of the casting, and their position and font style should
be consistent with the ones specified in the drawing.
Düzenleyen Marcello 2024-23-Temmuz Saat 06:40
|
Aktif Konular 
Üye Listesi 
Arama 
Yardım
Kayıt Ol 
Giriş
Gitar-tr.com FORUM : Gitar-tr.com Tanisma Toplantisi !!!
Konu: Are there any technical specifications th
